www.Catch-A-Mouse.net or Call 1 855 410 8797
How to catch a mouse:
Step 2 is: "Plug Holes"
Once you find out where they are going, and find their actual holes
they made, now you can begin to plug those holes.
This is copper mesh or steel wool works
almost as good!

Purchase Guaranteed Rats & Mice Removal

Most of our clients already have steel wool
which can work just as well as this copper

The advantage of the copper mesh, is that you
can use larger pieces and cut off what you
need. Where as the steel wool generally
comes in smaller pieces.
Text Us Below For Any Questions.
Make sure we are "ONLINE" before
you text us!
Otherwise we wont get your
Email Us: info@Catch-A-Mouse.Net
or 1 855 410 8797 or 1 416 410 8797
Wearing gloves and a dust mask during handling of the rodent detection stations is recommended. However, the powder used in
the stations is environmentally-friendly, completely non-toxic and rated by the FDA as safe for use in food handling areas and as
an indirect food additive.

Placement Spacing

In all interior applications the, rodent detection stations should be placed 15' to 25' apart. For exterior applications, placement
should be no more than 15' apart.

Interior Use

The use of this rodent detection and tracking system is intended to monitor rodent activity anywhere this activity is suspected: in
basements, crawl spaces, attics, garages, out buildings, warehouses, food processing plants, storage facilities, restaurants and
offices. Each station has an access point at each end, which have been sealed for transport. These must be opened at time of

Basements: place the rodent detection system stations on foundation walls where the stations fit and can be secured if needed.
Crawlspaces: place the rodent detection system stations on or along the foundation walls.
Attics: placement of the rodent detection system stations should be along the reachable perimeter walls.
Garages / Out Buildings: placement of the rodent detection system should be along the interior perimeter walls.

Exterior Use

Walk along the exterior of the structure you are inspecting, placing the stations along the perimeter wall approximately every 15’
apart where rodent ativity is suspected. Placing on clean solid ground will produce better results than an area littered with leaves
and or thick foliage. Some landscape pruning may be needed to set the rodent detection system stations down properly and to
follow the rodent’s activity during inspections. Each station has an access point at each end, which have been sealed for
transport. These must be opened at time of installation.

Inspect preferably after dusk or pre-dawn approximately 3 to 7 days after installation. In outdoor applications, inspect during dry
weather. If heavy rain is in the same day forecast, it is best to delay initial setting.

Each rodent detection system area should be checked thoroughly. In addition to checking the stations on the perimeter for
activity with the UV flashlight, special attention should be paid to the underside of shingles, missing foundation masonry, door
bottoms, etc. A second and third inspection is recommended at 7 to 10 day intervals until all locations are found. Life
expectancy of the bait is approximately 4 to 8 weeks. This will vary depending on the amount of rodents in the area and
moisture. Discard after use in a safe manor subject to state or local ordinances.

Prior to or during the sealing of all holes found it may be necessary to set rodent traps in the structure being inspected to remove
the rodent population. Traps should be set in active areas inside the structure adjacent to exterior access points found and all
traps should be set per trap label, also safe and out of the way of children and pests. Humane mouse traps can also be set in
the same fashion. Check all traps daily.

Permanent sealing products will need to be procured depending on where and how big these access points are. Some
recommended products are Hydrolic Cement, and ¼” galvanized hardware cloth or copper mesh for interior use (only). Soft
materials like expanding foam are not a solution for hole filling.

The rodent detection system system can be used as monitors during regular pest services and inspections. It is important to
view the bait through the side holes. When empty, new stations will need to be ordered.

Finally place 1 Ratzapper for every 1200 square feet of space to cover. Place the Raticator near the movement points of the rats
and mice. The Ratzapper will kill any rodents still trapped inside your home or office which is usually a combination of those that
were inside your walls when you sealed their holes shut. Note: Don't seal last inside hole until you've set up The Ratzapper. It is
recommended that you use both the Raticator immediately after you detect their movement and preferably locate their outside
If you have anything unsure or questions, text us or call us
during business hours 1 855 410 8797
or 1 416 410 8797 skype: ezeric1
Here are all the technical details.
All 3 steps are here: Tracking, Stopping and Killing!